Účet Kontakt
Váš košík
DPD a FedEx – termín doručení najdete u produktu
Potřebujete poradit? Zeptejte se naší AI

Termistor Creality CR-200B PRO Creality 3D příslušenství

Termistor Creality CR-200B PRO Creality 3D příslušenství
Termistor Creality CR-200B PRO Creality 3D příslušenství
548,22 Kč
PDF
PDF

Doprava a vrácení zboží

Předpokládané doručení středa 9. prosince
Budeme vás průběžně informovat prostřednictvím našeho podrobného systému sledování zásilek
Možnosti platby
Platební kartaVisaMastercardPayPalApple PayGoogle PayBankovní převod

Položte otázku – AI asistent odpoví hned.

Popis

Unlike generic thermistors that force you to guess wiring or splice cables, this Creality CR-200B Pro thermistor is a direct-fit replacement with the exact XH2.54 connector and 1-meter silicone-insulated lead, so you spend minutes swapping it in—not hours troubleshooting. The glass bead NTC 100K sensor with a 3950K beta value delivers the precise temperature feedback your hotend needs for stable extrusion and clean prints.

Highlights

  • NTC 100K ohm resistance at 25°C with 3950K B-value (±1%) for accurate hotend temperature measurement
  • Glass bead sensor head (approx. 3 mm diameter × 5 mm length) withstands up to 260°C
  • Pre-terminated XH2.54 2-pin connector plugs directly into Creality mainboards—no soldering
  • 1-meter silicone-insulated cable resists heat and flex fatigue in cable chains
  • Compatible with CR-200B Pro, Ender-3 series, CR-10 series, CR-6 SE and many other Creality models

In daily use

Installation is straightforward: remove the old thermistor from the heater block, insert this glass bead into the retaining hole (screw or clamp depending on your hotend), and connect the XH2.54 plug to the thermistor port on the control board. The silicone insulation stays flexible even after hours of printing, and the ±1°C typical accuracy keeps your firmware's thermal protection reliable. If your printer suddenly reads -14°C or shows a thermal runaway error, this is the part that fixes it.

Full specifications

  • Product type: Hotend thermistor (temperature sensor)
  • Sensor type: NTC 100K thermistor
  • Resistance at 25°C: 100 kOhm
  • B-value: 3950K ±1%
  • Maximum operating temperature: 260°C
  • Sensor head: Glass bead, approx. 3 mm diameter × 5 mm length
  • Cable length: 100 cm (1 meter)
  • Connector: XH2.54 2-pin
  • Material: Glass, copper, silicone insulation
  • Accuracy: ±1°C (typical)
  • Voltage rating: DC 5V (signal circuit)
  • Compatible products: Creality CR-200B Pro, Ender-3 series, CR-10 series, CR-6 SE and other compatible Creality models

Final note

Keep a spare thermistor in your toolkit—this is one of the most common failure points on Creality printers, and having the right connector from the start saves you from emergency downtime.

Parametry

Parametry
Kategorie
Díl 3D tiskárny
Kompatibilní produkty
Creality CR-200B Pro, Ender-3 Series, CR-10 Series, CR-6 SE
Materiál
Glass, Copper, Silicone
Model
CR-200B Pro Thermistor
MPN
3103020133
Typ
Hotend Thermistor
Typ produktu
Termistor
Velikost
Sensor head: 3mm x 5mm; Cable length: 100cm
Značka
Creality
Vývoj ceny za posledních 6 měsíců
Termistor Creality CR-200B PRO Creality 3D příslušenství
Aktuální
548,22 Kč
Nejnižší 7 d.
539,88 Kč
Nejvyšší 7 d.
548,22 Kč
Změna za 24 h
+0,09 Kč   +0%
Změna za 7 d.
+8,34 Kč   +2%
Změna za 30 d.
0,00 Kč   0%

Napsat recenzi

Hodnocení *
Poznámka: HTML se nepřekládá!

Stejná řada a alternativy

12

Populární produkty v této kategorii

8
Prodávající: UAB KUR LT · Gariūnų g. 57-14, LT-02300 Vilnius, Litva · IČO 303192950 · DIČ LT100008198612 · Odesíláme z EU (Litva)
WhatsApp
Messenger
Dobrý den, jsem AI asistent DistriNode. Pomohu vám najít produkty, porovnat možnosti, vytvořit cenovou nabídku v PDF nebo otevřít požadavek na podporu.
Všechny kategorie